Steel Plate Products. Carbon & High Strength Low Alloy (HSLA) Structural Steel Plate. A36; A572 Grade 42, 50, 60, 65; CSA G40.21 Grade 44W, 50W, 50A; A709 Grade 36 ASTM A572 - SSABThe ASTM A572 specification is the Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel for plates used in general construction and structural applications. ASTM A572 includes five grades with specified minimum yield strengths of 42, 50, 55, 60, and 65 ksi, respectively. For applications where notch toughness is important, consult SSAB for specific Charpy V-notch toughness
ASTM A572 Grade 50 plate thickness tolerance. ASTM A572 Grade 50 plate is HSLA structure steel under ASTM A572/ A572M santdand. It is usually calculated by theory weight. Due to thickness tolerance, the theory weight and actual weight of ASTM A572 Grade 50 plate will have certain differences. The ASTM A572 Grade 50 plate thickness tolerance shall conform to ASTM A6/A6M ASTM A572 Grade 50, 55, 60, 65 Steel Plates Specification ASTM A572 Grade 50, 60 Steel Plate Sepcification ASTM A572 standard is for high strength low alloy (HSLA) structural steel plate integrated with columbium-vanadium, the specification covers 5 grades of HSLA steel profiles, plates, sheet piling, and bars. ASTM A572 Steel Plate - A572 Grade 42, 50, 55, 60, 65 ASTM A572 steel plate is made of A572, a High-Strength Low-Alloy, Columbium-Vanadium Structural Steel. There are five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades 42 , 50 , and 55  are best for riveted, bolted, or welded structures.
ASTM A-588 Grade A/B ASTM A-588 Gr. A/B steel plate offers all the advantages of ASTM A572-50 but is produced with elevated levels of copper to add corrosion resistance. This weathering grade is often used in unpainted applications such as bridges, utility sign/poles and CSA G40.21 50W / 350W Structural, Carbon & HSLA Steel A high-strength, low-alloy steel plate grade specified within G40.21 of the Canadian Standards Association (CSA). This grade is utilized in a variety of structural applications. It is also referred to as 350W, which is its metric designation. This material is also available as Charpy tested when referenced with a "T", such as 50WT / 350WT. Carbon, Alloy and Stainless Steel PlateA572 Gr 50 3/16" 4" A572 Gr 42 >4" 6" A588 Gr A 3/16" 6" A/SA 516 Gr 70 3/16" 8" Carbon Steel Plate Low carbon steel produced to chemistry range only. Economical, machinable, weldable and formable. Fully killed over 11/2" for better internal soundness. Medium carbon steel produced to chemistry range only.
Farwest carries an A572 inventory flat bar range between 1-1/4 x 2 to 2-1/2 x 6-1/2. Common inventory lengths are 20, but shorter lengths can be saw cut to your specifications. Longer than 20 requirements may require a mill volume minimum to produce. Domestic stock available. Contact Farwest today for your requirements. High Strength Low Alloy - Farwest SteelFarwest minimizes waste by processing A572-50 coil 3/16 to 1/2 thick material 48 to 96 wide material to any length using Farwests state of the art Bradbury cut-to-length line. Farwest carries a A656-70 product for plate in 1. Grade 80 specifications. PRODUCT GUIDES - Central Steel & Wire Co.Product Guide - Steel Plate (contd) Form 1254 3/16/05 (Reprinted 5/27/15) Page 3 of 4 OVERVIEW Cold Reduced Plate Higher in quality (surface, flatness and shape). Maintains flatness after shearing, burning, or laser cutting and lower in cost. Flatness Defect Causes
B For plates up to 10 in. [254.0 mm], excl, in thickness, the tolerance under the specified thickness is 0.010 in. [0.25 mm]. C For circles, the over thickness tolerances in this table apply to the diameter of the circle corresponding to the width ranges shown. For plates Plate McneilusASTM A572 Gr50. ASTM A572 is a high strength low alloy steel that offers a higher strength than plain carbon steel plates plus ductility, weldability, formability, toughness and fatigue strength. A572 meets a minimum strength requirement (dependent on grade) and provides good workability and Sheet McneilusASTM A572 Gr50/Gr60. A572 is a high strength low alloy steel that offers a higher strength than plain carbon steel plates plus ductility, weldability, formability, toughness and fatigue strength. A572 meets a minimum strength requirement (dependent on grade) and
Our stock includes a range of sizes and grades that can be difficult to find from a single supplier, including A36 /SA36, A572 Grade 50, A516 Grade 70, A514, AR400, AR500, 1020, 1045, 4140, ABS Grade A, ABS Grade AH36, ABS Grade DH/EH36 and API 2H Grade 50. Steel Plate Comparisons Precision Grinding, Inc.Considered a mild steel due to hardness. A572-42 A572-50:A572 grade 50 steel plate is a high-strength, low-alloy plate, specified for bridges, higher strength structural duties, and light pressure vessel requirements. Recommended for riveted, bolted, or welded structures, such as Gussets and Bridge Plates, when intended for construction of Steel Reference Guide - Glosser SteelAvailable in A992/A572-50 (Grade 50) and A588 specifications. Theoretical Dimensions and Properties for Designing. glossersteel VISIT O ESITE losser Steel Service enter M. G L O S S E R & ASTM A572 - High-Strength Low-Alloy Steel Plate ASTM A588 - High-Strength Low-Alloy Steel Plate
Designated as W shapes, wide flange shapes are generally used as beams or columns. They are doubly-symmetric with substantially parallel inside flange surfaces. Depth sizes range from 4 to 36, and lengths from 20 to 60. Available in A992/A572-50 (Grade 50) and A588 specifications. A572 Structural, Carbon & HSLA Steel Plate - Chapel SteelASTM A572 A high-strength low-alloy steel plate that is utilized in a variety of structural applications. This specification is produced in Grades 42, 50, 55, 60 & 65, the grades representing the yield strength. Plates that are 4 and thicker are made to a 42 KSI yield, although material can be modified to reach the 50 KSI min yield.