BS 5950 ; Design data home . Structural products Rolling Tolerances to EN 10219-2:1997 for cold formed Square and Rectangular Hollow Sections . Designation:Property Tolerance Depth BS EN 10162:2003 - Cold rolled steel sections. Technical This European Standard specifies dimensional and cross-sectional tolerances for cold rolled steel sections produced on roll-forming machines. It applies to cold-rolled sections for general use (standard sections) produced from steels conforming to BS EN 10025, BS EN 10142 and BS EN 10147 and in the form of rectangular L, U, C, Z and Omega cross sections as well as split tubes.
BS EN 10210-1 specifies the technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product. BS EN 10210-2 :2006 HOT FINISHED STRUCTURAL buy bs en 10210-2 :2006 hot finished structural hollow sections of non-alloy and fine grain steels - part 2:tolerances, dimensions and sectional properties from nsai BS EN 10210-2 :2006 HOT FINISHED STRUCTURAL buy bs en 10210-2 :2006 hot finished structural hollow sections of non-alloy and fine grain steels - part 2:tolerances, dimensions and sectional properties from sai global
BS EN 10210-2 - Hot finished steel structural hollow sections Part 2:Tolerances, dimensions and sectional properties Published by BSI on May 31, 2019 A description is not available for this item. Chapter 45:Structural steel ICE manual of Construction This chapter concentrates on the specification of hot-rolled and tubular steel structures to BS EN 10025 and BS EN 10210 and their corresponding design standards, BS EN 1993:Eurocode 3 and formerly BS 5950. It also covers other types of steel, such as cold-formed steel to BS EN 10346 and stainless steel to BS EN European Standard EN 10219-1 :1997 has the status of a composition are based on DIN EN 10025 and DIN 10113-1 to DIN 10113-3. The DIN Standards and the Stahl-Eisen-Werkstoffblatt (Iron and steel material specification) (SEW) corresponding to the European documents referred to in clause 2 of the EN are as follows:
Tolerances. For tolerances on shape, reference should be made to BS EN 10034 for UB, UC and bearing piles. For tolerances of other sections, reference should be made to the above standards. Extracts giving the main tolerance details are given in the design section. Units. The dimensions of sections are given in millimetres (mm). Mass is given National (UK) Structural Steelwork Specification - What Is Generally, all products should be built according to one of the reference standards in BS EN 1090-2. The product standards specified by NSSS for material dimensions, tolerances and properties include:BS EN 10219-1 for cold formed hollow sections; BS EN 10210-1 for hot finished hollow sections; BS EN 10025-2 for rolled sections PED Certified OHSAS 18001:2007 ISO 9001 :2008 ISO 2.2 Standards on dimensions and tolerances (see 7.7.1) EN 10017, /\ion-a//oy steel rod for drawing and/or cold rolling Dimensions and tolerances. EN 10024, Hof ro/led Paper flange I sections - Tolerances on shape and dimensions. EN 10029, Hot rolled steel plates 3 mm thick or above - Tolerances on dimensions, shape and mass
Rolling tolerances to System.String for Parallel flange channels (PFC) Designation:Property:Range:Tolerance mm:mm:Height h:h = 65 ±1.5:65 < h = 200 ±2.0:200 < h = 400 ±3.0 Rolling tolerances to System.String for Hot-Finished Tolerance:Outside diameter D ±1.0% with a min of ±0.5 mm and a max of ±10 mm:Thickness t:Welded 10%:Seamless 10% but between 10% and 12.5% may occur over not more than 25% of the circumference:Note:Positive deviation is limited by mass tolerance:Measured at the centre of the length:Straightness (x or y direction) 0.20% L:Mass Section properties - Dimensions & properties - Blue Book BS 5950; BS EN 10210-2:2006; Hot-Finished Rectangular Hollow Sections Rolling tolerances Section properties Section properties View other design data (BS 5950):Effective section properties - For sections subject to axial compression
Channels to BS 4:Part 1:1993 (as per 4th Edition). Angles to BS 4848:Part 4:1972 (as per 4th Edition). Structural hollow sections to EN 10210:Part 2:1997. 6th Edition, 2001 Complete revision of the 5th edition, 1997, updating the information with the standard BS 5950-1:2000. The Blue Book - SteelConstructionfoHot-finished structural hollow sections to BS EN 10210-2 Comprehensive design data is also provided for bolts and welds, rolling tolerances are given, and there are comprehensive sets of explanatory notes for both the Eurocodes and BS 5950 data. References - Blue Book - Steel for LifeBS EN 10210 Hot finished structural hollow sections of non-alloy and fine grain structural steels BS EN 10210-1:1994 Technical delivery requirements (Replaces BS 4360:1990) Replaced by BS EN 10210-1:2006 BS EN 10210-2:1997 Tolerances, dimensions and sectional properties. (Replaces BS 4848-2:1991) Replaced by BS EN 10210-2:2006